The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
What are your beliefs on Installing A Bathtub?
Mounting a bathtub isn't precisely rocket science, but it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard job. If the old bathtub is conveniently available, the task can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub and place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will need a helper to vacate the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed task, it is better to consider employing one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This write-up will assist you set up a new tub in your washroom if you have actually currently bought a brand-new tub as well as do not require to change the arrangement of your previous water supply pipes.
Your devices as well as product checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly problematic as a result of the restricted gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washers are in area between the tap and also the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former kind needs to be connected to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bath tub in the required placement. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the tub till the spirit level checks out level.
To install faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water supply and examine all joints as well as new pipework for leakages and also tighten them if required. Load the bath tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least once as this will certainly settle it into its last setting.
Preparing for the Installment
To start with, the supporting structure provided with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a rigid seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, leading to difficulties with moisture as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the bath tub with water before securing, to enable the motion experienced when the tub remains in use. The sealant can break fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently offered on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our excerpt about Installing A Bathtub. Thank you so much for finding the time to read through our piece of content. Sharing is nice. Helping others is fun. Thanks for going through it.
Automated Marketing Report this page